• ▸The Syvecs Suzuki Jimny JB74 plug in ecu brings a new level of engine management control to the Suzuki Jimny range with a complete replacement Engine Control Module.
• ▸Supports both the manual and automatic transmission models.
• ▸The Syvecs Plug in kit comes complete with:
• ▸-NTK Lambda Sensor
• ▸-NTK Loom
• ▸-4Bar Map Sensor
• ▸-Air Charge Temperature Sensor
• ▸By simply plugging in the kit, a whole new level of control is available which allows turbo and supercharger installations to be safely managed and controlled.
• ▸Syvecs Jimny Features:
• ▸- Flat Shift/GearCut On Manual Transmission. Allowing Full throttle shifts
• ▸- Rev matching on downshift with manual transmission
• ▸- Support for automatic transmission with monitoring of line pressure and custom torque reductions.
• ▸- Flex Fuel control.
• ▸- Fully functional with every other module on the Car.
• ▸- 8 Injector support
• ▸- Forced induction support, requires External Map sensor and Air Charge Temp sensor
• ▸- Closed loop Lambda control using supplied NTK Lambda
• ▸- DBW support with cruise control (Option only if the correct parts are fitted)
• ▸- Rolling antilag / pit lane limiter strategies, great for building boost on a roll.
• ▸- Adjustable traction control strategies based on lateral G and individual wheel speed monitoring.
• ▸- Adjustable launch control.
• ▸- Limp Protection strategies
• ▸- 12 switchable maps with the ability to select desired engine map, boost level, traction and launch control levels through optional rotary switch
• ▸- Individual Cylinder Knock control
• ▸- Live tuning of every aspect of the engine’s calibration.
• ▸- Fully adjustable closed loop boost control with launch level adjustments and trims for turbo speed, air charge, engine coolant temp, exhaust gas temps etc..
• ▸- Built in data logging using a market leading analysis software of up to 8 hours, with data rates at up to 1000hz.
• ▸- Anti-theft and valet modes.
• ▸- Super fast connection via RJ45 Ethernet port for live tuning anywhere in the world or even remotely if on track if connected to one of our Wifi modules.
• ▸- Configurable engine safety trips on all important parameters like oil temperature, oil pressure.
• ▸- Fuel pump control of both main, and sub pumps, as well as relative fuel pressure monitoring and limiting in the event of fuel pressure dropping on boost.
• ▸- Run up to 7bar map sensors.
• ▸- Control high or low impendence injectors.
• ▸- Ability to fit any type of external sensor to monitor and trigger safety trips from anything from crank case pressure to damper position.
• ▸- Ability to use any size DBW throttle body e.g. Chevrolet LS7.
• ▸- Wet and Dry – Wet and dry nitrous control with ability to drive solenoids directly and control n20 heaters via pressure monitoring.
• ▸- Ability to control any external vehicle features based on sensor inputs e.g. Adjustable rear wing linked to G force or exhaust control valves.
• ▸- Connect any race series dash or even one of our Syvecs edition SDM display units.
• ▸- View any input live with built in scope up to 1000hz.
• ▸And much, much more!

This kit may require additional sensors to function on your setup. We strongly recommend contacting us to discuss your project details before purchasing.

Bundle Offer: Purchase this kit with an Optimum Engine Mapping calibration service and save on costs! Contact us for a combined hardware + calibration quote.

⚠ For off-road and competition use only. Not legal for use on pollution-controlled vehicles. Not emissions compliant. Installation and use on public roads may violate federal, state, or local laws. Purchaser assumes all responsibility for compliance with applicable regulations.